Hans,
Excellent work. The approach was well thought out. Curious though, did the test aircraft have the new teflon conduits? I am planning to change the conduits in my '65 260 in mid June. The same test procedure should produce good data regarding the benefits of new conduits vs. the originals in my airplane. I have less than 25 hours on a complete gear overhaul per the 1000hr AD so I believe my airplane is as close to "nominal" as you can get.
Would it be possible to borrow the same test apparatus for a before and after comparison of gear/transmission loads relative to new style conduits?
Chris
 |
International Comanche Society A maintenance forum for ICS members to share knowledge and learn about their Comanche. Problems? - Contact Administrator at: Webmaster |
Gear Retraction Load Test Results
17 posts
• Page 1 of 2 • 1, 2
Gear Retraction Load Test Results
by Hansmeister » Mon Apr 20, 2009 1:15 am
- Attachments
-
Comanche Gear Motor Load Tests.doc- (5.12 MiB) Downloaded 272 times
-
Hansmeister - ICS member
- Posts: 802
- Joined: Thu Jun 27, 2002 5:44 pm
- Location: Kah-li-forn-yah
-
Zach Grant L1011jock - Technical Advisor
- Posts: 1404
- Joined: Mon Mar 22, 2004 4:35 pm
- Location: Indianapolis KEYE
by Hansmeister » Mon Apr 20, 2009 5:15 am
-
Hansmeister - ICS member
- Posts: 802
- Joined: Thu Jun 27, 2002 5:44 pm
- Location: Kah-li-forn-yah
by JIMICS2452 » Mon Apr 20, 2009 1:26 pm
-
JIMICS2452 - ICS member
- Posts: 254
- Joined: Sat Mar 09, 2002 9:26 pm
- Location: Pine Shadows Airpark - North Fort Myers, FL
by JIMICS2452 » Mon Apr 20, 2009 1:27 pm
-
JIMICS2452 - ICS member
- Posts: 254
- Joined: Sat Mar 09, 2002 9:26 pm
- Location: Pine Shadows Airpark - North Fort Myers, FL
-
Zach Grant L1011jock - Technical Advisor
- Posts: 1404
- Joined: Mon Mar 22, 2004 4:35 pm
- Location: Indianapolis KEYE
by Chris Kuyoth » Wed Apr 29, 2009 8:15 pm
- Chris Kuyoth
- ICS member
- Posts: 123
- Joined: Sun Jan 16, 2005 6:20 pm
by Hansmeister » Thu Apr 30, 2009 2:39 am
-
Hansmeister - ICS member
- Posts: 802
- Joined: Thu Jun 27, 2002 5:44 pm
- Location: Kah-li-forn-yah
by Chris Kuyoth » Thu May 28, 2009 2:30 pm
- Chris Kuyoth
- ICS member
- Posts: 123
- Joined: Sun Jan 16, 2005 6:20 pm
by Hansmeister » Thu May 28, 2009 6:55 pm
-
Hansmeister - ICS member
- Posts: 802
- Joined: Thu Jun 27, 2002 5:44 pm
- Location: Kah-li-forn-yah
by Chris Kuyoth » Fri May 29, 2009 2:10 pm
- Chris Kuyoth
- ICS member
- Posts: 123
- Joined: Sun Jan 16, 2005 6:20 pm
by Chris Kuyoth » Wed Jun 03, 2009 4:17 pm
Hans,
Just wanted to confirm that you were able to send the jack and attachment fixtures. I am hoping to start the project this weekend.
Thanks,
Chris
Just wanted to confirm that you were able to send the jack and attachment fixtures. I am hoping to start the project this weekend.
Thanks,
Chris
- Chris Kuyoth
- ICS member
- Posts: 123
- Joined: Sun Jan 16, 2005 6:20 pm
by Hansmeister » Wed Jun 03, 2009 5:43 pm
It's been sitting in my truck. I've been very busy trying to finish a technical report. It will go out today.
-
Hansmeister - ICS member
- Posts: 802
- Joined: Thu Jun 27, 2002 5:44 pm
- Location: Kah-li-forn-yah
by Hansmeister » Thu Jun 04, 2009 1:19 am
Cris, the box went out today via FedEx Ground.
Your tracking number is 468810710088188.
Your tracking number is 468810710088188.
-
Hansmeister - ICS member
- Posts: 802
- Joined: Thu Jun 27, 2002 5:44 pm
- Location: Kah-li-forn-yah
17 posts
• Page 1 of 2 • 1, 2
Return to Maintenance - Airframe
Who is online
Users browsing this forum: No registered users and 0 guests