Rajay Turbos

Rajay Turbos

Postby KJB » Sun Jun 08, 2008 10:53 am

KJB
ICS member
ICS member
 
Posts: 21
Joined: Sat Jun 07, 2008 9:28 pm
Location: Alicante/Spain

Postby Zach Grant L1011jock » Sun Jun 08, 2008 1:55 pm

"Keep it above 5 feet and don't do nuthin dumb!"
User avatar
Zach Grant L1011jock
Technical Advisor
 
Posts: 1404
Joined: Mon Mar 22, 2004 4:35 pm
Location: Indianapolis KEYE

Postby KJB » Tue Jun 10, 2008 9:24 pm

Hi Zach,
thanks for message. we do that recommended of you next weekend.
i`m sure we find it out.
we did it last week from Chicago over the North Atlantic to Spain.
Its only a turbo. Thats a peace of cake.
Regards
Klaus (KJB)
KJB
ICS member
ICS member
 
Posts: 21
Joined: Sat Jun 07, 2008 9:28 pm
Location: Alicante/Spain

Postby Tony Scarpelli » Tue Jul 15, 2008 7:31 am

I have a 250 with the Rajay STC.

I was developing only 2" mp above normal. We rebuilt the flapper valve gasket and it jumped to 6". We replaced the cable with a thicker guage and ensure that the waste gates close fully and now we can get 9"

So at 11k' I can get about 28" mp.

I need it to get at least 26" mp at 20,000' where I plan to fly it.

There are two new turbos, 2 two year old waste gates, newly rebuilt air box induction system and all new skeet hoses.

Any ideas?

We may send the Turbos back to mfgr to have them tested to see if they are developing all the pressure they are supposed too.
Last edited by Tony Scarpelli on Wed Oct 15, 2008 5:04 pm, edited 1 time in total.
Tony Scarpelli
ICS member
ICS member
 
Posts: 111
Joined: Thu May 08, 2008 11:47 am

Postby Tony Scarpelli » Tue Jul 15, 2008 7:33 am

Is there any way that a faulting fuel system can cause lower MP than otherwise? At altitude I notice the fuel pressure gage and sometimes the fuel flow meeter jump.
Tony Scarpelli
ICS member
ICS member
 
Posts: 111
Joined: Thu May 08, 2008 11:47 am

Postby Jay » Tue Jul 15, 2008 4:30 pm

Hi Tony:

Here is a compendium of advice I've received from various sources:

1. Any leaks, even pin holes, in the hoses will cause problems. Pressurizing the system with a shop vac and then spraying with soapy water while looking for bubbles is the accepted procedure.

2. Make sure that the soft round metal parts that the hoses attach to on the boxes are all still truly "round". One owner has told me he wraps those with a double layer of electrical tape then puts the hose over the tape to make sure there are no leaks around the clamps.

3. Pay close attention to the waste gates. Sometimes waste gates can bind up before they are fully closed.

4. Alternate Air Door and the flapper door seals are a problem area. You can try making your own seals out of silicon, but they have to be tight.

5. Blow out proof exhaust gaskets are recommended on the stacks.

6. Whenever you take the system apart you want to use all new gaskets, don't re-use an old one.

Little leaks make a bigger difference than you might think. The first time I had my system worked on they leak checked it, and the A&P said "we only found a couple of tiny leaks". I said humor me and seal them up, and the result was a 5" pick up.

Good luck,

Jay
Jay
PA 30 N7702Y
User avatar
Jay
ICS member
ICS member
 
Posts: 473
Joined: Tue Sep 30, 2003 10:59 pm
Location: Portland, Oregon

Postby Charlie Tripp » Thu Aug 14, 2008 4:08 pm

User avatar
Charlie Tripp
ICS member
ICS member
 
Posts: 382
Joined: Thu Jun 27, 2002 5:38 pm
Location: Brownsville, TN

Postby Zach Grant L1011jock » Fri Aug 15, 2008 6:45 pm

"Keep it above 5 feet and don't do nuthin dumb!"
User avatar
Zach Grant L1011jock
Technical Advisor
 
Posts: 1404
Joined: Mon Mar 22, 2004 4:35 pm
Location: Indianapolis KEYE

Rajay Turbos

Postby KJB » Sun Nov 02, 2008 11:35 pm

KJB
ICS member
ICS member
 
Posts: 21
Joined: Sat Jun 07, 2008 9:28 pm
Location: Alicante/Spain


Return to Maintenance - Powerplant

Who is online

Users browsing this forum: No registered users and 4 guests

cron