Low Utilization Aircraft

Low Utilization Aircraft

Postby T210DRVR » Wed Oct 01, 2008 3:29 pm

As higher fuel prices push many of us to restrict our flying, I've found a product that may be worthy of considering to prevent corrosion in our engines. ASL CamGuard, http://www.aslcamguard.com/ , is a product that was developed to address this issue.

I don't have any interest in the product other than the potential for saving me from an early overhaul. I've used it in my three aircraft for the past two years and seen modest drops in wear metals. However, most important to me is preventing cam/lifter corrosion in my Lycoming engine. We all know that the camshaft location in our engine is not optimum in terms of assuring good lubrication. Long term storage can allow the cam to become pitted with rust.

I've changed from using Aeroshell 15-50 to Phillips 20-50 XC with CamGuard added. The net cost is almost identical, but I believe my engine benefits.

Your experience may vary, but this is the first product I've seen that may actually provide benefits to your engine. It is FAA certified for naturally aspirated certified aircraft engines.
User avatar
T210DRVR
ICS member
ICS member
 
Posts: 117
Joined: Sat May 03, 2008 4:31 am
Location: So. Oregon

Postby MULEFLY » Wed Oct 01, 2008 10:17 pm

T2...

FWIW I believe that Zach Grant (L1011jock) uses the cam guard with AeroShell 15W50... he mentioned that at the recent Comanche Pilot Proficiency Program that was held at Watertown, WI

Jim
Last edited by MULEFLY on Thu Oct 02, 2008 12:00 am, edited 1 time in total.
MULEFLY
ICS member
ICS member
 
Posts: 900
Joined: Tue Jan 25, 2000 1:34 am
Location: Wisconsin

Postby Zach Grant L1011jock » Wed Oct 01, 2008 11:49 pm

Yes,
I have been using Camguard for several years now (even before it was "approved") and have had great results in a variety of engines. I have noticed among other things, a reduction in wear, reduced temps and friction, noticably smoother running engines with no ther changes, and yes it does work well at fighting corrosion! I have used it with Aeroshell 15w50, Aeroshell straight weight oils, Castrol Aviator straight weight oils, all with excellent results in both Lyc and Continental engines. I learned about it when I attended a forum put on by the chemist that developed it at OSH some years back. Tried it, liked it, use it religeously.
-Zach
"Keep it above 5 feet and don't do nuthin dumb!"
User avatar
Zach Grant L1011jock
Technical Advisor
 
Posts: 1404
Joined: Mon Mar 22, 2004 4:35 pm
Location: Indianapolis KEYE

Postby T210DRVR » Thu Oct 02, 2008 12:27 am

User avatar
T210DRVR
ICS member
ICS member
 
Posts: 117
Joined: Sat May 03, 2008 4:31 am
Location: So. Oregon

Postby Zach Grant L1011jock » Thu Oct 02, 2008 12:29 am

"Keep it above 5 feet and don't do nuthin dumb!"
User avatar
Zach Grant L1011jock
Technical Advisor
 
Posts: 1404
Joined: Mon Mar 22, 2004 4:35 pm
Location: Indianapolis KEYE

Camguard

Postby Trevor Laundy » Sat Oct 18, 2008 12:52 pm

Trevor Laundy
PA30 C Turbo non de=iced
User avatar
Trevor Laundy
ICS member
ICS member
 
Posts: 41
Joined: Wed Dec 10, 2003 12:48 am
Location: New Zealand / Great Britain

Postby Zach Grant L1011jock » Sat Oct 18, 2008 4:10 pm

"Keep it above 5 feet and don't do nuthin dumb!"
User avatar
Zach Grant L1011jock
Technical Advisor
 
Posts: 1404
Joined: Mon Mar 22, 2004 4:35 pm
Location: Indianapolis KEYE

Postby Kristin Winter » Sat Oct 18, 2008 6:01 pm

Kristin
User avatar
Kristin Winter
ICS member
ICS member
 
Posts: 1299
Joined: Tue Aug 09, 2005 5:21 pm
Location: Northern California

Postby MULEFLY » Sat Oct 18, 2008 6:46 pm

MULEFLY
ICS member
ICS member
 
Posts: 900
Joined: Tue Jan 25, 2000 1:34 am
Location: Wisconsin

Postby Charlie Tripp » Sat Oct 18, 2008 10:51 pm

User avatar
Charlie Tripp
ICS member
ICS member
 
Posts: 382
Joined: Thu Jun 27, 2002 5:38 pm
Location: Brownsville, TN

Postby Alan Cheak » Sun Oct 19, 2008 2:51 am

A good loser... is still a loser.
User avatar
Alan Cheak
ICS member
ICS member
 
Posts: 142
Joined: Sun Jan 12, 2003 8:17 pm
Location: Peachtree City, GA KFFC

Camguard

Postby 15384 » Sun Oct 19, 2008 3:43 am

15384
ICS member
ICS member
 
Posts: 115
Joined: Wed Nov 26, 2003 5:06 pm

Postby Zach Grant L1011jock » Sun Oct 19, 2008 4:01 am

"Keep it above 5 feet and don't do nuthin dumb!"
User avatar
Zach Grant L1011jock
Technical Advisor
 
Posts: 1404
Joined: Mon Mar 22, 2004 4:35 pm
Location: Indianapolis KEYE

Postby Alan Cheak » Sun Oct 19, 2008 5:27 am

A good loser... is still a loser.
User avatar
Alan Cheak
ICS member
ICS member
 
Posts: 142
Joined: Sun Jan 12, 2003 8:17 pm
Location: Peachtree City, GA KFFC

Postby Jay » Mon Oct 20, 2008 4:07 pm

Jay
PA 30 N7702Y
User avatar
Jay
ICS member
ICS member
 
Posts: 473
Joined: Tue Sep 30, 2003 10:59 pm
Location: Portland, Oregon

Next

Return to Maintenance - General

Who is online

Users browsing this forum: No registered users and 11 guests

cron